LED Track Spot Light System reflektor Rail LED Ceiling Track Spotlight Lamp 12W 20W 30W CREE Store Lights 2 3 Wire Phase Circuit

LED Track Spot Light System reflektor Rail LED Ceiling Track Spotlight Lamp 12W 20W 30W CREE Store Lights 2 3 Wire Phase Circuit
  • Продавецironandwinetickets.org
  • Список ценUS $777.45piece
  • Продажная ценаUS $777.45piece
  • ДоставкаБесплатная доставка
  • Рейтинги3,6 (457)

Oписание продукта

 

RC 4axle Multi QuadCopter UFO RTF/ARF:KK V2.3 Circuit board+1000KV Motor+30A ESC+Lipo+F450 Flamewheel+T8FB TX&R8EF RX

 

(assembly required buyers)
F02192-A RC 4axle Multi QuadCopter UFO RTF/ARF:
HJ 450 450F Nylon Fiber Flamewheel Frame *1
A2212 1000KV Motor installed 
base*4
JMT 25A ESC*4
V2.3 Circuit board*1
Programmer Firmware Loader 
USB*1
1045 Propeller*2 pair
 
JMT 11.1V 2200mah 20c lipo battery *1
Relate wire
Charger+adapter * 1 set
 
RadioLink T8FB Transmitter and R8EF receiver *1
   
       

 

 

 

HJ 450 450F Nylon Fiber Flamewheel Frame Airframe kit

Fetures:

by advanced engineering material,super 
strong & smooth.
High quality and strong ability of 
anti-fall, lower maintenance cost.
Compact design with small numbers of 
components, you can assemble it by youself quickly and 
easily.
Suitable for both beginners and senior
Excellent quad-copter 
products.
- Support KK MWC by new disign PCB board(Not Included)
 
Speicifications:
Color: Red + White + Black
Shaft distance: 17.7in/450mm
- Net weight: 0.65lb/282g - by advanced 
engineering material,super strong & smooth
- Kit(need you assemble yourself)

 

aeProduct.getSubject()aeProduct.getSubject()aeProduct.getSubject()aeProduct.getSubject()

KKMulticopter v5.5 Circuit board V2.3 

 

 

As for the USB,this is the new version,we will send the the new version,thanks!

For the program method,please contact meaeProduct.getSubject()

 

 

 

1. Simple structure, Easy 
to Maintain and Debug Control
 
2. Relying on 
potentiometer adjust gyro sensitivity.
 
3. Full servo signal 
output, support normal ESC / analog servo
 
4. Support for single-axle 
/ UFO, Y3 3-axle, Y4-type 3-axle, 4 axle, 6 axle, V22 flight 
mode
 
5. Supports 4-axle "+" and 
"X" flight mode, support for six-axle "HEXA6" and "Y6" flight 
mode.
   
FlyCam MultiCopter 
Controller Blackboard(kkMultiCopter)
     

A 2212 A2212 1000KV Brushless 

Outrunner Motor W/ Mount *4pcs
 
KV: 1000 
Max Efficiency: 80% 
 
Max Efficiency Current: 4-10A 
(>75%) 
Current Capacity: 12A/60s 
 
No Load Current @ 10V: 0.5A 
 
No. Of Cells: 2-3 Li-Poly 
 
Motor Dimensions: ?27.5 x 30mm 
 
Shaft Diameter: ?3.17mm 
 
Weight: 47g/set 
Including: 1 
set 2212 1000KV Brushless Outrunner Motor with Mounts *4
 
11.1V 20C 2200Mah Lipo Battery *1 pcs

Specification:

Output:11.1V(3S1P)2200mAh
Weight 
About:193g
 
This Li-poly 
battery features high efficient and high discharge,use a inspection machine to match packs, suitable for All Align trex 450 
rc heli and other professional model 
airplanes, cars, and guns.
 
Max 
Continuous Discharge: 10C, Burst Discharge: 15C. Normal operating temperature is 
approx. 40-65°C(within 80% of rated 
discharge). Max. temperature: 80°C.
NOTE:
When using 
high energy Li-poly Battery, please do not over-discharge, over-charge 
batteries, or result over-high temperature. Discharging 
capacity can\'t exceed 80% of the max capacity after full 
charging to ensure a good cycle performance. Recommend to full 
charge 
a brand new battery before using and only discharge the battery 50% for first 5 
times 
to make a good efficiency of the battery. Please make it a habit to always count 
time 
for flight, or please set a low voltage protection on ESC (Cell voltage after 
stopping using can not lower than 3.2V). Do not use the 
battery at insufficient of voltage.
 
Do not expose batteries to sunshine or store/ charge 
batteries at the temperature up to 35°C in a airtight car. 
The environment high temperature could cause the damage or the 
danger 
of burst. If the battery becomes hot while high current discharging or 
flying,
please do not charge the battery immediately. Wait to 
cool down(about 20 mins), then inspect to recharge. If against follow the original 
factory using rules, possibly cause the battery to inflate or 
any dangerous accident happens.
       

Product Features:

1.Custom designed firmware
Be applicable to helicopter, fixed wing, glider, multi-copter. Special firmware will be designed according to your model types.
 
2. Inheritance industrial designing
Cooperate with professional designer of AT9. T8FB adds innovation and independent design concept, can be a perfect choice for your plane.
 
3. Online upgrade
Unique upgrade mode, through simulator port and special Radiolink upgrade cable, no need for driving programs and is perfect compatible with all OS.
 
4. Humanized operation
On the basic experiences of modelers, T8FB, simplify the operation, makes it easy to use even without illustration.
 
5. Long-tested anti-interference
Follows the technology of wireless spread spectrum used by T7F, makes it possible to control freely in condition of same frequency interference.
 
6. S-BUS, PPM and PWM signal output at the same time
Compatible with FUTABA S-BUS port, also supports cable connection input one by one, S-BUS, PPM and PWM signals are possible to use at the same time.
 
7. Incredible price
Incredible price own high level specification.

 
T8FB Technical Parameters

1. Size: T8FB - 173*102*206mm, R8EH - 48.5*21*11mm.
2.Weight: 0.47kg(including R8EH)
3.Frequency: 2.4GHz ISM band(2400MHz~2483.5MHz)
4.Modulation mode: GFSK
5.Channel bandwidth: 400KHz
6.Band width:1200KHz
7.Spread spectrum: FHSS
8.Adjacent channel rejection: >36dBM
9.Transmitter power: <100mW (20dBM)
10.Sensitivity: -104dBM
11.Speed rate:38kbps
12.PWM output: 1.0ms~2.0ms
13.Section precision: 2000, 0.5us per section
14.Cycle:15 ms/per frame
15.Radio T8FB operating voltage: 4.8V~18V
16.Radio T8FB operating current: <110mA
17.Receiver R8EH operating voltage: 4.6~10V
18.Receiver R8EH operating current: <30mA
19.Control distance: more than 1000 meters air, the actual control distance depends on the flying environment.

 

aeProduct.getSubject()
    
 

aeProduct.getSubject()